|
British Columbia |
BC Safety Authority B.C. Safety Authority Suite 200 - 505 Sixth Street New Westminster, B.C. V3L 0E1 Toll free: 1-866-566-SAFE (7233) Phone 604-660-6286 Fax 604-660-6215 BCSA web site Fees vary - see B.C. Fee Schedule B.C. application form must be used for all registrations. B.C. statutory declaration form (and guide) must be used for fitting registrations. British Columbia Act - revised April 2004 Summary of Registration Requirements: Pressure Vessel - 1 set of drawings with P.Eng stamp, 1 set of design calculations Fitting - 1 set of drawings, 1 set of design calculations and 1 original notarized statutory declaration form. |
|
Alberta |
Alberta Boilers and Safety Association 9410-20 Avenue Edmonton, Alberta Canada, T6N 0A4 Contact: Design Survey Phone 780-437-9100 Fax 780-437-7787 ABSA web site Fees vary by size and complexity of the vessel Fee Schedule Alberta application form must be used for all registrations. Alberta statutory declaration form must be used for fitting registrations. Alberta does not always require a P.Eng. stamp on submissions - call the above number for details. Summary of Registration Requirements: Pressure Vessel - 2 sets of drawings, 1 set of design calculations Fitting - 2 sets of drawings, 1 set of design calculations and 2 original notarized statutory declaration forms. Note: ABSA will accept drawings without a P.E. Stamp for fittings and U stamp vessels, however a stamp is required for Division 2 designs. Officially, if a stamp is required, vessel drawings must be stamped by an Alberta professional engineer. This rule is not enforced. |
|
Saskatchewan |
Codes and Standards Compliance Office Boiler and Pressure Vessel Safety Board Technical Safety Authority of Saskatchewan 330-1855 Victoria Avenue Regina, SK Canada S4P 3T2 Toll-free: 1-866-530-8599 Regina: 306-787-1443 Fax 306-787-9273 TSASK Website
Boiler and Pressure Vessl Safety Forms Application form for the Registration of Designs Saskatchewan statutory declaration form Summary of Registration Requirements: Pressure Vessel - 2 sets of drawings with P.Eng stamp, 1 set of design calculations Fitting - 2 sets of drawings, 1 set of design calculations and 1 original notarized statutory declaration form. |
|
Manitoba |
Manitoba Labour and Immigration Workplace Safety and Health Division 500-401 York Avenue Winnipeg, Manitoba Canada, R3C 0P8 General Inquiries 204-945-3373 Fax 204-945-4556 Manitoba website This Manitoba application form must be used for all boiler, pressure vessel and heat exchanger registrations. Additional forms are available for fittings and piping. Manitoba statutory declaration form Summary of Registration Requirements: Pressure Vessel - 2 sets of drawings with P.Eng stamp, 2 sets of design calculations Fitting - 2 sets of drawings, 2 sets of design calculations and 2 original notarized statutory declaration forms. |
|
Ontario |
Technical Standards and Safety Authority 14th Floor, Centre Tower 3300 Bloor Street West Toronto, Ontario Canada, M8X 2X4 Phone: 416-325-2000 Fax 416-231-5366 TSSA website Ontario application form must be used for all registrations Ontario statutory declaration form must be used for all fitting registrations Summary of Registration Requirements: Pressure Vessel - 2 sets of drawings with Ontario P.Eng stamp, 1 set of design calculations Fitting - 2 sets of drawings, 1 set of design calculations and 2 original notarized statutory declaration forms. Pressure vessel drawings must be stamped with an Ontario professional engineer's stamp. This rule is enforced by the TSSA. |
|
Quebec |
Service de l'inspection de la fabrication D'appareils sous pression 545, boulevard Crémazie est, 4 ème étage Montréal, Quebec Canada, H2M 2V2 Phone: 514-873-6459 or 1-866-262-2084 Fax: 514-873-9936 La Régie du bâtiment website English: Pressure Vessels Page Many of the employees are bilingual in French and English. Summary of Registration Requirements: Note: Officially, vessel drawings must be stamped by a Quebec professional engineer. This rule is not enforced. Pressure Vessel - 3 sets of drawings with P.Eng stamp, 1 set of design calculations Fitting - 3 sets of drawings with P.Eng stamp, 3 original notarized statutory declaration forms and 1 set of design calculations or test data. |
|
New Brunswick |
See ACI Central |
|
Nova Scotia |
See ACI Central Boiler and Pressure Vessel information and link to Nova Scotia Act |
|
Prince Edward Island |
See ACI Central Prince Edward Island Act |
|
Newfoundland and Labrador |
See ACI Central Newfoundland and Labrador Act |
|
Yukon |
See ACI Central |
|
North West Territories |
See ACI Central |
|
Nunavit |
See ACI Central |
|
ACI Central |
ACI Central, Inc. 20 McAuley Court Charlottetown, PE Canada C1A 9M7 Phone: 902-566-1975 Fax: 902-566-3133 ACI website See Province or territory for fees Ask about review rates if your project is complicated. One review fee applies to all Provinces / Territories covered by ACI Central Allow 10 working days for review. A Professional Engineer's stamp is required, but does not have to be Canadian. A purchase order and cover letter with contact information is required before review will start. A link to all ACI Pressure Vessel Application Forms can be found on their website: www.acicrn.com/ Registration Requirements: Pressure Vessel - 2 sets of drawings with P.Eng stamp, 1 set of design calculations, Pressure Vessel Registration Form (Design Information). Fitting - all except Newfoundland - 2 sets of drawings, 1 set of design calculations and 1 original notarized statutory declaration form. Fitting - Newfoundland - 2 sets of drawings with P.Eng stamp, 1 set of design calculations and 2 original notarized statutory declaration forms. |